Clean Coal Technology

2021, v.27;No.134(04) 180-188

[打印本页] [关闭]
本期目录(Current Issue) | 过刊浏览(Archive) | 高级检索(Advanced Search)

循环流化床预热燃烧试验研究及数值模拟
Experimental study and numerical simulation of preheating combustion in circulating fluidized bed

潘飞,朱建国,刘敬樟
PAN Fei,ZHU Jianguo,LIU Jingzhang

摘要(Abstract):

循环流化床预热燃烧过程中,预热燃料在下行燃烧室的燃烧过程至关重要。为了研究预热燃料在下行燃烧室中的流动和燃烧特性,采用计算流体力学软件Fluent,结合试验手段,对不同二次风喷口配风方式下,预热燃料在下行燃烧室的燃烧过程进行试验及数值模拟,对比了不同配风方式下,流动特性、温度特性、组分浓度分布特性以及氮氧化物排放特性的差异。结果表明,预热燃料在下行燃烧室的燃烧过程中,二次风会卷吸烟气在下行燃烧室上部产生回流,稀释反应物,在中心喷口配风时回流区域更大。不同配风方式下,下行燃烧室中的温度分布不同。环形喷口配风时下行燃烧室中的温度峰值为1 459 K,而中心喷口配风时下行燃烧室的温度峰值为1 555 K,同时环形喷口配风时下行燃烧室的高温区域较小,温度分布更加均匀。环形喷口配风时,预热燃料和二次风的混合更加充分,高温煤气和空气的反应更加强烈,有助于燃料的着火及升温。而中心喷口配风时下行燃烧室顶部的CO和H_2等还原性气体浓度较高,有助于还原NO_x。同时较高的温度促进了气化反应,生成更多的CO和H_2,在燃尽风喷入前的区域形成还原性气氛,有助于进一步还原NO_x。二次风中心喷口配风时,更多的氮氧化物被还原,尾部烟气中的NO_x排放浓度为107×10~(-6),二次风环形喷口配风时,尾部烟气中的NO_x排放浓度为121×10~(-6)。
In the process of preheating combustion of circulating fluidized bed, the combustion process of the preheated fuel in the down-fired combustor(DFC)is very important. In order to study the flow characteristics and combustion characteristics of the preheated fuel in the DFC,the computational fluid dynamics software Fluent was used, combined with experimental methods, to test and simulate the combustion process of the preheated fuel in the DFC under different secondary air nozzles. the differences in flow characteristics, temperature characteristics, component concentration distribution characteristics and nitrogen oxide emission characteristics under different air distribution methods were compared. The results show that during the combustion process of the preheated fuel in the DFC,the secondary air can entrain the flue gas and reflow in the upper part of the down-fired combustor to dilute the reactants, and the recirculation area is larger when the air is distributed at the central nozzle. Under different air distribution modes, the temperature distribution is different. The peak temperature in the DFC is 1 459 K when the air is distributed at the annular nozzle, while the temperature peak is 1 555 K when the central nozzle is distributed. At the same time, when the air is distributed at the annular nozzle, the high temperature area is smaller and the temperature distribution is more evenly. When the air is distributed at the annular nozzle, the mixing of preheating fuel and secondary air is more sufficient, and the reaction between high temperature gas and air is more intense, which is helpful to the ignition and heating of fuel. When the air is distributed at the central nozzle, the concentration of CO and H_2 at the top of the DFC is higher, which helps to reduce NO_x. What′s more, a higher temperature promotes the gasification reaction, forming a reducing atmosphere, which is conducive to further reduce NO_x. When the central nozzle is used for air distribution, more nitrogen oxides are reduced, the NO_x emission in the tail flue gas is 107×10~(-6). When the annular nozzle is used for air distribution, the NO_x emission is 121×10~(-6).

关键词(KeyWords): 循环流化床;预热燃烧;数值模拟;燃烧特性;NO_x排放
circulating fluidized bed;preheated combustion;numerical simulation;combustion characteristics;NO_x emission

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金面上资助项目(51676178)

作者(Author): 潘飞,朱建国,刘敬樟
PAN Fei,ZHU Jianguo,LIU Jingzhang

DOI: 10.13226/j.issn.1006-6772.CE20110901

参考文献(References):

扩展功能
本文信息
服务与反馈
本文关键词相关文章
本文作者相关文章
中国知网
分享