张嘉鸣,王子兵,郭珊,王绍龙,李世成
ZHANG Jiaming,WANG Zibing,GUO Shan,WANG Shaolong,LI Shicheng

• 1:华北理工大学冶金与能源学院

摘要(Abstract)：

蓄热式加热炉作为冶金行业重要设备,主要用于钢坯加热,以高、转炉煤气等为燃料,采用周期换向燃烧方式,在换向时烧嘴会向大气中排放煤气,换向动作导致的煤气放散率高达3%～7%,造成资源浪费和环境污染。为了节约资源,减小污染,解决蓄热式加热炉在燃烧换向时造成的煤气放散问题,最直接的回收利用途径是将公共管道内的残留煤气吹扫至炉膛进行燃烧。现对某钢厂一座160 t/h蓄热式加热炉进行改造,在现有操作平台上加装烟气吹扫系统,烟气吹扫系统是从煤气烟气管道上引出一路用来吹扫管道,通过引风机将煤气烟气加压作为吹扫气源,将吹扫管道与煤气换向阀底部相接,通过调节原有煤气换向程序,配合响应快速的控制阀门进行吹扫过程的启停。吹扫时,管道内提前加压后的烟气喷出,迅速将公共管道内残留的煤气吹至炉膛内进行燃烧,以此达到放散煤气减排的效果。最后进行了工程实践,对比了改造前后系统炉温、炉压、CO减排效果以及经济性。已改造的加热炉,单次吹扫体积为37.05 Nm~3,按照加热炉单次换向周期60 s,加热炉年工作时间按330d计算,年吹扫体积为1 760.62万Nm~3,吹扫效率按照90%计,则年煤气排放量为1 584.56万Nm~3,对应厂用煤气价格为0.13元/Nm~3,一年可节约成本206万元。蓄热式加热炉反吹系统可实现CO减排率高达90%以上。
As an important equipment in the metallurgical industry,the regenerative heating furnace is mainly used for billet heating. Using the high gas and converter gas as fuel and adopting the periodic reversal combustion method,the burner emits off-gas into the atmosphere during the reversal combustion process. The gas emission rate caused by the reversing action reaches to 3%-7%,causing waste of resources and environmental pollution. In order to save resources,reduce pollution,and solve the problem of gas emission caused by regenerative heating furnaces during combustion reversal,the most direct way of recycling is to sweep the residual gas in public pipes into the furnace for combustion. Now,the 160 t/h regenerative reheating furnace of a steel plant is being modified,and a flue gas purge system is installed on the existing operating platform. The flue gas purge system is to lead all the way from the gas flue gas pipeline for purging.The gas flue gas as the purge gas source is pressurized by the induced draft fan,and the purge pipe is connected with the bottom of the gas reversing valve. By adjusting the original gas reversing program and cooperating with the fast response control valve,the start and stop of the scanning process is carried out. During the purge,the flue gas pressurized in advance in the pipeline is ejected,and the residual gas in the public pipeline is quickly blown into the furnace for combustion,so as to achieve the effect of gas emission reduction.At last,the engineering practice was carried out,and the system furnace temperature,furnace pressure,CO emission reduction effect and economy before and after the transformation were compared. For the renovated heating furnace,a single purge volume is 37.05 Nm~3. According to the single reversal cycle of the heating furnace for 60 s,the annual working time of the heating furnace is calculated based on 330 days and the annual purging volume is 17.606 2 million Nm~3. If the purging efficiency is calculated as 90%,the annual gas emission is 15.854 6 million Nm~3,and the corresponding factory gas price is 0.13 yuan/Nm~3,which can save 2.06 million yuan a year. With the application of the regenerative heating furnace backflushing system,the CO emission reduction rate is as high as 90%.

关键词(KeyWords)： 蓄热式加热炉;烟气吹扫;煤气换向;节能减排
regenerative heating furnace;flue gas purging;gas reversing;energy conservation and emissions reduction

Abstract:

Keywords:

基金项目(Foundation): 唐山市科技计划资助项目(18130210a)

作者(Author): 张嘉鸣,王子兵,郭珊,王绍龙,李世成
ZHANG Jiaming,WANG Zibing,GUO Shan,WANG Shaolong,LI Shicheng

DOI: 10.13226/j.issn.1006-6772.IF20080622

参考文献(References)：

• [1]KATSUKI M,HASEGAWA T.The science and technology of combustion in highly preheated air[J].Symposium(International) on Combustion,1998,27(2):3135-3146．
• [2]GUPTA A K.Thermal characteristics of gaseous fuel flames using high temperature air[J].Journal of Engineering for Gas Turbines and Power,2004,126(1):9-19．
• [3]RAFIDI N,BLASIAK W.Heat transfer characteristics of Hi TACheating furnace using regenerative burners[J].Applied Thermal Engineering,2006,26(16):2027-2034．
• [4]ISHII T.Numerical simulations of highly preheated air combustion in an industrial furnace[J].Journal of Energy Resource Technology,1998,120:276-284．
• [5]HASEGAWA T,TANAKA R.High temperature air combustionrevolution in combustion technology.part I:New findings on high temperature air combustion[J].JSME International Journal,Series B,1998,41(4):1079-1084．
• [6]SUGIYAMA S,SUZUKI N,KATO Y,et al.Gasification performance of coals using high temperature air[J].Energy,2005,30 (2/4):399-413．
• [7]CARPENTR P G.Control of Lukens'110-in plate mill reheat furnace at Conshohocken[J].Iron and Steel Engineer,1990,67(8):2-5．
• [8]戎宗义．国内外加热炉和热处理炉的现状和节能技术[J]．特殊钢,1999(5):37-41.RONG Zongyi.Current status and energy-saving technologies of heating furnaces and heat treatment furnaces at home and abroad[J].Special Steel,1999(5):37-41．
• [9]童庆年,袁玉琢．蓄热式燃烧技术在步进加热炉上的应用[J]．工业炉,2002(2):39-42.TONG Qingnian,YUAN Yuzhuo.Application ofregenerative combustion technology in walking heating furnace[J].Industrial Furnace,2002(2):39-42．
• [10]邢桂菊,祁海鹰,徐旭常．日本Hi TAC技术的发展对中国钢铁行业的启示[J]．钢铁,2002,37(9):67-71.XING Guiju,QI Haiying,XU Xuchang.Theenlightenment of the development of Hi TAC technology in Japan to the chinese iron and steel industry[J].Iron and Steel,2002,37(9):67-71．
• [11]霍存,徐先强,赵言喜．特大型蓄热步梁式加热的应用实践[J]．中国冶金,2008(8):32-34.HUO Cun,XU Xianqiang,ZHAO Yanxi.Application practice of extra large regenerative step-in beam heating furnace[J].China Metallurgical Industry,2008(8):32-34．
• [12]肖仕长．蓄热式燃烧技术在轧钢加热炉上的合理利用[J]．四川冶金,2008(4):40-43.XIAO Shichang.Reasonable use of regenerative combustion technology in steel rolling heating furnace[J].Sichuan Metallurgy,2008(4):40-43．
• [13]侯长连,胡和平．高效蓄热式工业炉的开发与应用[J]．钢铁,2010,37(1):65-67.HOU Changlian,HU Heping.Development and application of high-efficiency regenerative industrial furnace[J].Iron and Steel,2010,37(1):65-67．
• [14]张朝红,桂万根,李东,等．全分散换向技术在蓄热式加热炉上的应用[J]．工业炉,2003(3):13-15.ZHANG Chaohong,GUI Wangen,LI Dong,et al.Application of fully decentralized commutation technology in regenerative heating furnace[J].Industrial Furnace,2003(3):13-15．
• [15]张先珍,戴德彦．换向时间对蓄热式燃烧的影响[J]．冶金能源,2005(4):30-32.ZHANG Xianzhen,DAI Deyan.Effect of commutation time on regenerative combustion[J].Metallurgical Energy,2005 (4):30-32．
• [16]张卫军,王芳,齐凤升,等．推钢式板坯加热炉流场、温度场和浓度场的模拟研究[J]．东北大学学报(自然科学版),2011,32(2):266-269.ZHANG Weijun,WANG Fang,QI Fengsheng,et al.Simulation study on flow field,temperature field and concentration field of push-type steel slab heating furnace[J].Dong Journal of North University(Natural Science Edition),2011,32(2):266-269．
• [17]李克文．步进式加热炉内热工过程的数值模拟[D]．武汉:华中科技大学,2007.LI Kewen.Numerical simulation of the thermal process in the stepping furnace[D].Wuhan:Huazhong University of Science and Technology,2007．
• [18]吴青娇．加热炉内流动、燃焼及传热的数值模拟和优化研巧[D]．长沙:中南大学,2010.WU Qingjiao.Numerical simulation and optimization of flow,burning and heat transfer in heating furnace[D].Changsha:Central South University,2010．
• [19]MORGADO T,COELHO P J,TALUKDAR P.Assessment of uniform ture Assumption in zoning on the numerical simulation of a walking beam reheating furnace[J].Applied Thermal Engineering,2015,76:496-508．
• [20]CASAL J M,PORTEIRO J,MGUEZ J L,et al.New methodology for CFD three-dimensional simulation of a walking beam type reheating furnace in steady state[J].Applied Thermal Engineering,2015,86:69-80．
• [21]潘丽萍,李宝宽,贺铸．推钢式板坯加热炉炉衬损耗的数值模拟[J]．钢铁研究,2015,43(4):42-46.PAN Liping,LI Baokuan,HE Zhu.Numericalsimulation of lining loss of push-steel slab heating furnace[J].Iron and Steel Research,2015,43(4):42-46．
• [22]顾新新．加热炉内传热及流动特性的数值研究[D]．青岛:青岛科技大学,2012.GU Xinxin.Numerical study of heat transfer and flow characteristics in heating furnace[D].Qingdao:Qingdao University of Science and Technology,2012.